Preparation:

1. Perform sampling in designated areas with proper ventilation (e.g., fume hoods or gas cabinets).
2. Ensure the area is free of ignition sources and unnecessary personnel.
3. Keep spill kits and emergency eyewash stations nearby.

Container Preparation:

1. Use pre-labeled, compatible, and clean sample containers with tight-sealing lids.
2. Label sample containers with:
   • Material name
   • Date of sampling
   • Sampler’s initials
   • Hazard classification

4.2 Sampling Procedure

1. General Sampling Guidelines:
   1. Ensure sampling is performed under controlled conditions to minimize material exposure.
   2. Avoid direct contact with the hazardous material during sampling.
   3. Collect only the required amount of sample to minimize waste and exposure.

less
Copy code

2. Sampling of Liquids:
   1. Use chemical-resistant pipettes or transfer pumps to collect samples.
   2. Do not pour liquids directly from large containers; use controlled tools to prevent splashes.
   3. Place collected samples into sealed, pre-labeled containers.
   4. Wipe external surfaces of sample containers to remove any residues.
3. Sampling of Solids:
   1. Use clean scoops or spoons to transfer solid samples carefully.
   2. Minimize dust formation by transferring solids slowly and under ventilation.
   3. Place samples into airtight, pre-labeled containers to avoid spills.
4. Sampling of Gases:
   1. Use gas sampling equipment, such as gas-tight syringes, pumps, or gas sampling tubes.
   2. Ensure gas sampling is performed in ventilated enclosures or gas cabinets.
   3. Transfer the sample into compatible, sealed vials or cylinders designed for gas containment.
5. Post-Sampling Activities:
   1. Seal all sample containers immediately and verify proper labeling.
   2. Clean sampling tools with appropriate cleaning agents or dispose of them as per waste guidelines.
   3. Record sampling details in the Hazardous Material Sampling Log (Annexure 1).

4.3 Post-Sampling Handling

1. Sample Transfer:
   1. Transport samples in secure, secondary containers to the designated analysis or storage areas.
   2. Avoid dropping, shaking, or exposing samples to temperature extremes during transfer.

less
Copy code

2. Decontamination:
   1. Clean the sampling area and tools with compatible decontaminants.
   2. Dispose of used PPE, wipes, and any contaminated materials as hazardous waste.
3. Documentation:
   1. Log all sampling information in the Hazardous Material Sampling Log (Annexure 1).
   2. Include details such as the material name, quantity, sampling date, and sampler’s name.

4.4 Emergency Procedures

1. Spills During Sampling:
   1. Stop operations immediately and contain the spill using spill kits.
   2. Report large spills to the Safety Officer and evacuate the area if necessary.

less
Copy code

2. Exposure Incidents:
   1. Skin contact: Remove contaminated clothing and rinse the area for 15 minutes.
   2. Eye contact: Use an eyewash station for at least 15 minutes.
   3. Inhalation: Move to fresh air and seek immediate medical attention.

5) Abbreviations, if any

• SDS: Safety Data Sheet
• PPE: Personal Protective Equipment

6) Documents, if any

• Hazardous Material Sampling Log
• Incident Reports
• Safety Data Sheets (SDS)

7) Reference, if any

• OSHA Standard for Hazardous Materials (29 CFR 1910.120)
• NIOSH Sampling and Analysis Guidelines

8) SOP Version

Version: 1.0

Annexure

Template 1: Hazardous Material Sampling Log

 
 
 
Date
 
Material Name
 
Type (Solid/Liquid/Gas)
 
Quantity
 
Sampled By
 
Remarks
 
 
 
DD/MM/YYYY
 
Material Name
 
Liquid
 
XX ml
 
Employee Name
 
Sample Collected