SOP Guide for Pharma

Tablets: SOP for Temperature and Humidity Control in Coating Areas – V 2.0

Auditor

Tablets: SOP for Temperature and Humidity Control in Coating Areas – V 2.0

Standard Operating Procedure for Temperature and Humidity Control in Coating Areas

Department Quality Control
SOP No. SOP/TAB/128/2025
Supersedes SOP/TAB/128/2022
Page No. Page 1 of 6
Issue Date 01/03/2026
Effective Date 06/03/2026
Review Date 01/03/2027

1. Purpose

To define the procedure for controlling and monitoring temperature and humidity levels in the coating areas during the tablet manufacturing process to ensure uniform and high-quality coating.

2. Scope

This SOP applies to the temperature and humidity control systems in the coating areas used for the production of film-coated tablets. Proper environmental conditions are essential for achieving uniform coating.

3. Responsibilities

4. Accountability

The QC Manager is accountable for ensuring that the temperature and humidity levels are maintained within specified ranges. The Facilities Manager is responsible for the maintenance and calibration of the environmental control systems.

See also  Tablets: SOP for Testing Tablet Edges for Chipping in Process - V 2.0

5. Procedure

5.1 Temperature and Humidity Range Specifications

  1. Temperature in the coating area should be maintained within the range of 20°C to 25°C (68°F to 77°F).
  2. Relative humidity should be controlled between 40% and 60% to ensure consistent coating quality.
  3. Any deviation from these ranges must be immediately corrected, and corrective actions should be documented in the deviation report (Annexure-1).

5.2 Monitoring Frequency

  1. Temperature and humidity should be continuously monitored throughout the coating process.
  2. Data should be recorded at regular intervals (e.g., every 30 minutes) to ensure that environmental conditions remain within the specified limits.
  3. For manual recording, ensure that readings are logged in the temperature and humidity log (Annexure-2).
  4. For automated systems, ensure that the data is saved and stored electronically for traceability.

5.3 Equipment Calibration and Maintenance

  1. Temperature and humidity control equipment should be calibrated at regular intervals, typically every six months or according to the manufacturer’s instructions.
  2. Ensure that calibration records are maintained and reviewed by QA for compliance with internal standards (Annexure-3).
  3. Perform maintenance of the environmental control systems as per the scheduled preventive maintenance plan to ensure proper functioning.

5.4 Adjustment of Temperature and Humidity

  1. If temperature or humidity deviates from the acceptable range, corrective actions must be taken immediately:
    • Adjust air conditioning, heating, or humidifying systems to bring temperature and humidity levels within the specified range.
    • If the adjustment is not successful, document the issue, and notify the Facilities/Engineering Department for further troubleshooting.
    • Monitor the levels continuously after making adjustments to confirm that the environmental conditions remain within specifications.
See also  Tablets: SOP for Using Fluidized Bed Processor in Tablet Manufacturing - V 2.0

5.5 Documentation

  1. Record all temperature and humidity readings in the temperature and humidity log (Annexure-2), including the time of reading, the measured values, and any corrective actions taken.
  2. Document any deviations from the required temperature and humidity ranges in the deviation report (Annexure-1), along with corrective actions.
  3. Ensure all records are signed and dated by the responsible personnel and reviewed by QA.

5.6 Acceptance Criteria

  1. The temperature and humidity levels must remain within the specified ranges of 20°C to 25°C and 40% to 60% relative humidity, respectively, for the entire duration of the coating process.
  2. If any reading falls outside the acceptable range, the batch should not proceed until the issue is resolved, and corrective actions are documented.

5.7 Post-Coating Actions

  1. Once the coating process is completed and the environmental conditions are stable, proceed with the drying, packaging, and storage of tablets as per the next steps in production.
  2. Ensure that the temperature and humidity control equipment is cleaned, calibrated, and maintained regularly.

See also  Tablets: SOP for In-Process Friability Testing for Tablets - V 2.0

6. Abbreviations

7. Documents

  1. Temperature and Humidity Log (Annexure-2)
  2. Deviation Report (Annexure-1)
  3. Calibration Record (Annexure-3)

8. References

9. SOP Version

Version: 2.0

10. Approval Section

Prepared By Checked By Approved By
Signature
Date
Name
Designation
Department

11. Annexures

Annexure-1: Deviation Report

Deviation Date Batch Number Deviation Description Corrective Action Responsible Person
15/12/2025 Batch 001 Humidity > 60% for 30 minutes Adjusted humidifier settings and rechecked John Doe

Annexure-2: Temperature and Humidity Log

Time Temperature (°C) Humidity (%) Action Taken
10:00 AM 22°C 50% No action needed

Annexure-3: Calibration Record

Equipment Calibration Date Next Calibration Due Calibration Status
Temperature Controller 01/02/2025 01/08/2025 Calibrated

Revision History:

Revision Date Revision No. Revision Details Reason for Revision Approved By
01/01/2024 1.0 Initial Version New SOP Creation QA Head
01/02/2025 2.0 Updated calibration and control processes Improved control measures QA Head
Exit mobile version